Payment & Shipping Terms:
|Product Name:||Temperature Measuring Sterilizer||Name:||Body Inspection|
|Temperature Measurement Range:||-20 ℃ ~ 100 ℃||Temperature Measurement Error:||± 0.1 ℃|
|Pass Rate:||1.5 Seconds Per Person (average Data)||Working Voltage:||3.3 ~ 5V, Working Current: 5mA|
|Working Power:||AC110-220V, 50 / 60HZ||Net Weight:||30KG|
|Material:||304 Stainless Steel|
Body Inspection Measuring Sterilizer,
Bank Temperature Measuring Sterilizer
Thermal infrared sensor, high sensitivity probe
High sensitivity Non-contact Automatic Temperature measuring sterilizer
It is suitable for stations, hospitals, schools, banks, office buildings, army courtyards, office halls of various institutions, residential quarters, large factories, and vegetable markets.
Temperature measuring post disinfection machine uses high-precision infrared temperature sensor, the sensing distance is 0-5cm,
With high precision and high resolution, immune to the environment and sunlight, small interference, measurement error ± 0.1 ℃ at room temperature. The initial temperature setting is 37.3 ° C (adjustable). When the detection door is working, it will display an alarm when the detected actual body temperature exceeds 37.3 ° C. After the pedestrian measures the temperature, they can reach into the sterilizer and drop the disposable disinfectant solution automatically after sensing, so as to achieve the disinfection effect and prevent the virus in their hands from being constantly transmitted.
Working temperature: -20 ℃ ~ 45 ℃
Temperature measurement range: -20 ℃ ~ 100 ℃
Temperature measurement error: ± 0.1 ℃
Pass rate: 1.5 seconds per person (average data)
Working voltage: 3.3 ~ 5V, working current: 5mA
Working power: AC110-220V, 50 / 60HZ
Disinfection solution: 1L as standard, 1000 persons / time
Power: ﹤ 20W
Net weight: 30KG
Dimensions: 1850mm (height) x 150mm (width) x 330mm (depth)
Material: 304 stainless steel
Waterproof rating: IP55
Product function diagram introduction and alarm prompt:
The installation of this equipment is very simple. It is recommended to choose an environmental area where the room temperature does not exceed 30 degrees and the low temperature does not fall below -10 degrees. After selecting the installation area of the device, fix the device at the bottom and plug it in and use it.
Note: Please choose a level ground to install the equipment to prevent the equipment from tilting; the bottom must be fixed firmly to avoid falling down.
Ø Power on: Plug in the power supply (this product is powered by AC 220V), touch the power button on the monitor for about 6 seconds, and after you hear the "Didi Didi" four beeps, the display is turned on.
Ø Start the temperature measurement: When the device is turned on, or the device is in the standby state, you need to start the temperature measurement. You only need to use the hand or forehead to irradiate the temperature in the temperature measurement area. When you hear a "Didi", the display turns on. The temperature measurement function has been started.
Ø Detection: Pedestrians enter the detection range and bring their foreheads close to the detection area (5-20CM). When they hear a "Didi" from the device, the detection is completed and takes 1-2 seconds; the detection results will appear on the display immediately.
Ø Disinfection: This equipment is equipped with an automatic induction disinfection machine. When the pedestrian detection result is normal body temperature, the pedestrian puts his hand under the automatic induction disinfection machine, the hands from bottom to top, the automatic induction disinfection machine drips disinfectant, and the pedestrian rubs Leave after hand.
Ø Standby: When the device does not perform temperature measurement for more than 60 seconds, the display of the device will go out, and the device's temperature measurement function will enter the standby state.
1. Do not measure for a while or immediately after breastfeeding
2. Do not drink, eat or exercise before or during the measurement
3. If there is dust, hair or sweat on the temperature measuring probe, please wipe it with alcohol or disinfecting water immediately
4. Don't leave the temperature measurement area when you don't hear the "drop" at the end of the measurement.
5. Please try to measure in the specified measurement area
Warranty and after-sales service
Dear Sir or Madam: Hello!
Thank you for patronizing our products! To protect your rights and interests, please read the contents carefully after purchasing:
Thanks for your trust and glad to cooperated with you. To protect your rights and interests, please read the contents carefully after purchasing:
The following conditions are not within the scope of free maintenance, and the paid services are available to provide. Please note:
Ø Product damage caused by failure to install or use according to the instruction manual
Ø Over the warranty period
Ø Damage caused by using non-Our company accessories
Ø Product disassembled or repaired by personnel not authorized by our company
Ø Product damage caused by unexpected factors or human actions, such as mechanical damage, drop, severe oxidation of the product, etc.
Ø Damage caused by transportation, loading and unloading during customer's return
Ø Product damage caused by other irresistible natural forces such as earthquakes, fires, etc.
Ø Failure or damage caused by other problems than the design, technology, manufacturing, quality of the product itself
If there is obvious man-made hard object damage, cracks, severe deformation, etc., it will not be replaced. Users can purchase it separately.
Ø The warranty replacement is limited to the core parts, and the accessories such as packaging and various technical materials are not covered by the warranty replacement. If the equipment performance problem occurs within 15 days after the product is purchased, and the appearance is not scratched, you can directly replace the new product. Warranty replacement products must be tested by our company. If it is a good opportunity, it will be returned directly to the customer. If the fault is confirmed, the same model product will be replaced, and the defective spare parts replaced will belong to our company.
Ø Warranty: 1 year
Contact Person: bill